Search found 26 matches

are you sure there? usually a pushbutton that is black means its a normally closed not a normally open. so yes there would be a difference. you would want the normally open not the normally closed.
...

i had the same problem as you when i first tried to solder. it wouldnt work for me on the menus but when i was on the song lists it went nuts. as if i had it held down. now i of course became very fru ...

home depot and other such hardware stores. ask for plexiglass if you cant find it. no one there ever seems to know what lucite or an acrylic is. even if it is where they are stationed or whatever. hmm ...

i have never done that mod so i wouldn't know about that problem. but i have built my own metal pad. and to answer your question. i have never had a sensitivity problem. well unless you consider it a ...

yeah pretty much. if you have a radio shack by your place you should be able to pic one up. if not, try any electronic hobbyist shops. they would have them. either one of your wiring schemes would wor ...

well yeah that is how it works. your visual is correct.

now here's the thing each button (controller) has a + and -

as to the
1 2
-(| |)-

look.

when i made mine i didnt know which ...

what do you mean a solo pad? do you mean a home built and self design one? if so than yes i have. if not then explain a little better as to what your asking eh?

anyways as for the wiring question.. ...

ok you guys i still dont get this. i have built my pad. (works great by the way). and i still yet to encounter a static electricity problem. so what the hell are you guys doing to your pads? honestly ...

hey there mister paladin be a little nicer eh? not everyone comes into this kind of project with knowledge in electronics. so give the guy a break.

anyways yes its quite simple you solder one end ...

just the buttons my friends. i wasnt willing to risk the possible side effects of lights. anyways i used a mad catz controller for the circuitry part. works well. seems they are not pissy about the wh ...

I HAVE FINISHED MY PAD, AND IT IS SEXY!!!!!!!!!!!

well admitedly it still needs the arrow graphics but that is besides the point. IT IS DONE AND IT IS SEXY!!!!!!!!!!!!!!!

it works amazingly and ...

i like your design very inovative. well atleast i like the whole bracket substitute part. as for the rest...if it works it works i honestly dont know if it will work as you want. but yeah the the corn ...

hey why dont you just use solder with flux already in it? its a lot easier if you ask me. pretty much it looks like a 'wire' of solder with a hole in the middle. the hole is actually the flux. this st ...

cold solder joints do not effect the responsiveness of the pad. what they affect is the circuit itself. which means the wires in which you soldered to the circuit can come/break off. also it can cause ...

i used contact cement. it works wonders. anyways it explains how to use it on the can/container. but yeah it is reallly good and it works wonders. i used it to glue my metal to my acrylic. anyways hop ...

first off i would just like to say....My pad design owns! alright now that im done with that little bit of arrogance....i shall say something of relavence.

i doubt that the static that would/could ...

hey i wasnt trying to brag here or anything. i was just letting you know that i wasnt talking out of my buttocks and that i do have a basses in which to bass my answers on. in other words i was letting you ...

(never mind)

So... Has anyone tried modding a Cyber Groove pad?

I need some help here.

you may want to go to the soft pad/modding soft (or whatever they ca ...

ok lets see here. first off it seems that one of you has me beat for being the cheapest. ah well i still come second.

now to answer the lengthy and many questions.....

!. alright as far as the w ...

hey guys. i have just come to an amazing conclusion. i will be spending the least amount of money out of all of you. and i think i will be using way more materials.

anyways my cause for celebration ...